EFI System Partition

The EFI System Partition (also called ESP or EFISYS) is a FAT32 formatted physical partition (in the main partition table of the disk, not under LVM or software RAID etc.) from where the UEFI firmware launches the UEFI bootloader and application.

It is an OS independent partition that acts as the storage place for the EFI bootloaders and applications to be launched by the EFI firmware. It is mandatory for UEFI boot.

Warning: If dual-booting with an existing installation of Windows on a UEFI/GPT system, avoid reformatting the UEFI partition, as this includes the Windows .efi file required to boot it. In other words, use the existing partition as is and simply #Mount the partition.


Create the partition

The following two sections show how to create an EFI System Partition (ESP).

Note: It is recommended to use GPT for UEFI boot, because some UEFI firmwares do not allow UEFI-MBR boot.

It is recommended to keep ESP size at 512 MiB although smaller/larger sizes are fine. [1]

According to a Microsoft note[2], the minimum size for the EFI System Partition (ESP) would be 100 MB, though this is not stated in the UEFI Specification. Note that for Advanced Format 4K Native drives (4-KB-per-sector) drives, the size is at least 256 MiB, because it is the minimum partition size of FAT32 drives (calculated as sector size (4KB) x 65527 = 256 MiB), due to a limitation of the FAT32 file format.

GPT partitioned disks

Choose one of the following methods to create an ESP for a GPT partitioned disk:

MBR partitioned disks

Create a partition with partition type EFI System using fdisk. Proceed to #Format the partition.

Format the partition

After creating the ESP, you must format it as FAT32:

# mkfs.fat -F32 /dev/sdxY

If you used GNU Parted above, it should already be formatted.

If you get the message WARNING: Not enough clusters for a 32 bit FAT!, reduce cluster size with mkfs.fat -s2 -F32 ... or -s1; otherwise the partition may be unreadable by UEFI.

Mount the partition

Tango-view-fullscreen.pngThis article or section needs expansion.Tango-view-fullscreen.png

Reason: Add /boot/efi (Discuss in Talk:EFISTUB#ESP mount points)

In case of EFISTUB, the kernels and initramfs files should be stored in the EFI System Partition. For sake of simplicity, you can also use the ESP as the /boot partition itself instead of a separate /boot partition, for EFISTUB booting. In other words, after creating and formatting the EFI System Partition as instructed above, simply mount it at /boot.

Also see #Using bind mount.

Known issues


It is possible to make the ESP part of a RAID1 array, but doing so brings the risk of data corruption, and further considerations need to be taken when creating the ESP. See [3] and [4] for details.

Tips and tricks

Using bind mount

Instead of mounting the ESP itself to /boot, you can mount a directory of the ESP to /boot using a bind mount (see mount(8)). This allows pacman to update the kernel directly while keeping the ESP organized to your liking.

  • This requires a kernel and bootloader compatible with FAT32. This is not an issue for a regular Arch install, but could be problematic for other distributions (namely those that require symlinks in /boot). See the forum post here.
  • You must use the root= kernel parameter in order to boot using this method.

Just like in EFISTUB#Alternative ESP Mount Points, copy all boot files to a directory on your ESP, but mount the ESP outside /boot (e.g. /esp). Then bind mount the directory:

# mount --bind /esp/EFI/arch/ /boot

After verifying success, edit your Fstab to make the changes persistent:

/esp/EFI/arch /boot none defaults,bind 0 0

See also